Are there enough solder paste infront of the squeegee (app. 15 mm radius roll).
Does previous solder paste stick to squeegee?
Does the solder paste infront of squeegee drag instead of rolling?
Does the solder paste stay on the stencil surface?
Are apertures less than half of the pitch size?
Is the stencil thicker than 0.150 mm?
Are apertures clogging?
Is stencil deformed?
Is the green dye thicker or thinner than the pads?
Are ther any solder masks, stickers and etc. near misprinted?
Are tin coated pads smooth?
Is the viscosity of the solder paste too much?
Is solder paste old and dry?
Is the solder paste left on the stencil more than tens of minutes ?
Is it cold in printing area?
Is it uniform at squeegee edges?
Is squeegee blunt?
Are squeegee edges damaged?
Is squueegee speed too much for solder paste?
Is squueegee pressure too low? (for example less than 1kg/100mm squeegee length )
Are PCB supports weak?
Is squeegee too soft (less than 75 shores)
Is squeegee pressure to high? (for example more than 2kg/100mm through squeegee length).
Is seperation speed less than 0.5 mm/s or more than 10 mm/s?
3.Raglenin önündeki krem lehim yuvarlanmayıp sürükleniyor mu?
4.Krem lehim elek yüzeyinde mi kalıyor?
5.Açıklık genişlikleri bacak aralığının yarısından çok daha az mı?
6.Elek 0.150 mm den daha mı kalın?
7.Elek açıklıkları tıkanmış mı?
8.Elek hasar görmüş mü?
9.Kartlardaki yeşil boya adalardan daha kalın yada daha ince mi?
10.Hatalı baskının yakınında herhangi bir lehim maskesi, işaret mürekkebi etiket veya benzeri malzeme var mı?
11.Adalar kalay kaplaması yeterince düzgün mü?
12.Krem lehimin viskozitesi çok fazla mı?
13.Krem lehim eski ve kurumuş mu?
14.Krem lehim onlarca dakikadan uzun süre elek üzerinde bırakılmış mı?
15.Baskı alanı soğuk mu?
16.Ragle kenarları düzgün değil mi?
17.Ragle körelmiş mi?
18.Ragle kenarları zarar görmüş mü?
19.Ragle hızı krem lehim için çok fazla mı?
20.Ragle basıncı çok mu düşük? (yani 1kg/100mm ragle boyundan daha az)
21.Kart destekleri zayıf mı?
22.Ragle çok mu yumuşak ve krem lehimi kaşıklıyor mu?(yani 75 shore’dan az)
23.Ragle basıncı çok fazla ve krem lehimi kaşıklıyor mu? (yani ragle boyu için 2kg/100mm den daha fazla).
24.Ayrılma hızı 0.5 mm/s den az yada 10 mm/s den fazla mı?
PA
Email This email address is being protected from spambots. You need JavaScript enabled to view it.Latest from PA
- AssemCorp is authorized to sell all Transcend products in Türkiye
- World of electronics production meets in Munich
- AssemCorp is the exclusive representative of AMCOM in Turkey as of July 2023
- AssemCorp is among Fortune 500 companies!!
- SMTconnect exhibition is on 9-11 May 2023 Nuremberg
- How do I clean and take care of my desoldering tools?
- What is the best type of wool?
- IPC APEX EXPO will take place in January 24-26
- Wave vs Selective Soldering
- As of September 2022 AssemCorp starts working with Data I/O
- Elek Altı Temizleme Rulosu Nedir?
- Intelligent Memory announces partnership with AssemCorp
- SMTconnect exhibition is on 10-12 May in Nurnberg
- What is Solder Paste?
- 3M™ Novec™ Engineered Fluids can now be found in AssemCorp