FR-810B SMD Rework System

FR-810B SMD Rework System
FR-810B SMD Tamir SistemiFR-810B SMD Tamir Sistemi-1
670W high power and large volume hot air improves work efficiency. Vacuum pick up function for easy and safe removal of components. Possible to make a simple thermal profile by Chain Presets function High power and large air volumeFurther evolution of SMD rework station High power and large volume ...Devamını oku

4.33333 5 6 Product
6 Yorum


  • Açıklama
  • İndirme
  • Özellikleri
  • Yorum
  • Yorum Yaz

670W high power and large volume hot air improves work efficiency.
Vacuum pick up function for easy and safe removal of components.
Possible to make a simple thermal profile by Chain Presets function

High power and large air volume
Further evolution of SMD rework station

High power and large volume hot air for quick removal of components

A tool that can provide powerful hot airflow for repairing high heat capacity circuit boards that require high blow volume and high output, and sufficient hot airflow for appropriate blow volume and high output for high-density mounting substrates.

Efficiency improvement

The high volume airflow and high output of FR-810B make it possible to perform the same work in only one-third of the time required when using a conventional model. This reduces the thermal impact on boards and components.

* Examination of time taken for connector sections soldered onto a ceramic board to be heated to 200°C with maximum temperature and airflow settings selected.

* Single nozzles with an approximately 4mm diameter were used.

Improvements of FR-810B

On top of the features of FR-810, high power and large air volume, the new functions of vacuum pickup and pickup indicator have been given to FR-810B.
The 2 new functions make it possible to remove a component without damaging PWB.

・New type of nozzles for improvement of temperature characteristics
The new nozzle improves work efficiency with uniform heating by hot air convection inside the nozzle which is created due to vents on the nozzle top. (Only with BGA nozzle)

・Vacuum pickup function
The vacuum pickup function is to pick up a component with a suction pad and vacuum. It will pick a component only after the hot air melts solder joints.
This can avoid an error to peel off the land by removing a component with excessive force.

・Pickup indicator
By pre-setting pickup function, a component can be picked up automatically when solder is melted. At the same time, the indication comes up and the moment of picking up will be visible. Even a component and solder joints can not be seen as covered by a nozzle, easy and safe picking up is possible.

Use conventional HAKKO nozzles

Align the projection part, attach the conventional nozzle to the heater pipe.

*The heater pipe of HAKKO FR-810 (discontinued) has two projection parts. In order to use the conventional nozzle, put the conversion adaptor on the heater pipe that was included in your purchased HAKKO FR-810 as one of standard accessories.

Simple nozzle removal and easy maintenance

Nozzles can be quickly changed for many different types of components.
In addition, conventional nozzles are compatible. Heaters can also be easily and securely replaced.

Timer function

Timer function is to control the time of operation.
This can help to prevent parts from overheating and can improve the overall quality of rework.

Chain presets function for making a simple thermal profile

The chain presets function is to make a simple thermal profile by combining several preset conditions. (Up to 5 steps) This can improve work efficiency a lot by standardizing work time, avoiding overheating, improving repeatability of operation, and making difficult rework jobs easy.

Auto sleep and auto shutoff features

To ensure safety and conserve power, when the handpiece is placed in the handpiece holder, the auto sleep function will be activated and it will start cooling automatically.
If the handpiece has not been removed from the handpiece holder (e.g. Using it in a rework fixture) and it has been idle for 30 minutes, auto shutoff function will be activated. It will be automatically powered off.
Access to settings can be restricted by the password function.

With the use of Grip fixture, Board holder and Bottom heater, work conditions can be controlled even more strictly.

A low cost rework system can be assembled with a bottom heater, a grip fixture, and a board holder.

Packing List

Station with handpiece, Nozzle (Φ 4 mm), Handpiece holder, Vacuum pipe control knob L (with screw), Pads (qty 2 each of Ø3 mm, Ø5 mm, Ø7.6 mm), Heat resistant pad, Power Cord, Temperature distribution chart, Instruction manual

 Model No.  FR-810B
 Power consumption AC100V 700W
AC110V: 840W
AC120V: 820W
AC220V: 1.100W
AC230V: 1.200W
AC240V: 1.300W
 Temperature range  50 - 600ºC



 Power consumption  30W
 Air flow  1-9 (5 - 115L / dak)
 Dimensions  160 (W) × 145 (H) × 220 (D) mm
 Weight   1.5kg


Handpiece (Hot air)

 Power consumption AC100V :670W
AC110V: 810W
AC120V: 790W
AC220V: 1.070W
AC230V: 1.170W
AC240V: 1.270W
 Standard nozzle  Φ4mm (No. N51-02)
 Total length 250mm
 Weight  180g


* Total length and weight for handpiece (w/o cord, standard nozzle)
* Airflow capacity is rated as free flowing. Restrictions created by various nozzles may reduce the maximum airflow capacity.

Üretici: HakkoHakko
Yorum listesi:
Henüz yorum yazılmadı.
Oylama: ( 6 )

Bu öğe hakkında tavsiyelerde bulunun:

Sosyal Medya

AssemCorp'u sosyal medyada takip edin!


En Son Tweetler

TBMM’nin açılışının 100.yılında 23 Nisan Ulusal Egemenlik ve Çocuk bayramımız kutlu olsun. En büyük bayram bu bayram, herkese kutlu olsun. 🇹🇷🇹🇷🇹🇷
RT @NordsonASYMTEK: Conformal Coating and Bubbles – What you need to know to avoid reliability issues. Camille Sybert explains how to troub…
Happy Easter weekend 🐰 we will soon meet at healthier days 🤞🏻


AssemCorp Elektronik A.Ş.

  Şerifali Mah. Miras Sok. No:25 34775 Yukarı Dudullu Ümraniye İstanbul Türkiye

Telefon : +90 (216) 939 26 00
Faks : +90 (216) 909 31 53
E-Posta :
Web :
E-ticaret Sitemiz :
Facebook Sayfamız : Facebook Sayfamız